View CXA3185_169555.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CXA3185/3186N
All Band TV Tuner IC with On-chip PLL
Description The CXA3185/3186N is a monolithic TV tuner IC which integrates local oscillator and mixer circuits for VHF band, local oscillator and mixer circuits for UHF band, an IF amplifier and a tuning PLL onto a single chip, enabling further miniaturization of the tuner. Features * Low noise figure * Low power consumption (5 V, 54 mA typ.) * On-chip tuning PLL (3-wire bus format) * Selection of frequency steps 31.25 kHz, 50 kHz and 62.5 kHz * On-chip 4-output band switch Applications * TV tuners * VCR tuners * CATV tuners Structure Bipolar silicon monolithic IC 30 pin SSOP (Plastic)
Absolute Maximum Ratings (Ta = 25 C) * Supply voltage VCC1,VCC2 -0.3 to +5.5 VCC3 -0.3 to +10.0 * Storage temperature Tstg -55 to +150 * Allowable power dissipation PD 880
V V C
mW (when mounted on a substrate)
Operating Conditions * Supply voltage VCC1, VCC2 VCC3 * Operating temperature Topr
4.75 to 5.3 4.75 to 9.45 -20 to +75
V V C
Note) Electrostatic discharge strength is weak, and care should be taken in handling this IC.
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
--1--
E97944-TE
CXA3185/3186N
Block Diagram and Pin Configuration
CL DA CE FMT
1 2 3 4 5 6
Divider 14/15bit Band SW Driver Phase Detector Charge Pump Input Buffer Shift Register Divider 1/512,640,1024 REF OSC
30 29
VCC3 REFOSC
28 27
CPO CPE LOCK
BVL
BVH
LOCK Det
26
BU
7
USW Prescaler 1/8
25
IF OUT
VCC1
8
V.REG
Bias
24
GND
IF AMP
23
VCC2
MIXout1
9
Buffer
22 21 20 19
UOSCB2 UOSCE2 UOSCE1 UOSCB1
MIXout2 10 GND1 11 MS 12 VHFin 13 Buffer VHF MIX UHF OSC
18 Buffer UHFin1 14 UHFin2 15 UHF MIX VHF OSC 17 16
VOSC2 GND VOSC1
--2--
CXA3185/3186N
Pin Description Pin No. Symbol
22 100k 5k
Equivalent circuit
VCC2
Pin voltage (V)
Description
1
CL
1
--
Clock input.
22 100k 5k
VCC2
2
DA
2
--
Data input.
22 150k
VCC2
3
CE
3
50k
1.25 Enable pin. (when open)
4
FMT
30 VCC3 20k
5
BVL
4 5 6
ON : Vcc3 OFF : 0
6
BVH
7
4 : Output for FM TRAP. 5 : Power supply output for VL band. 6 : Power supply output for VH band. 7 : Power supply output for UHF band. The selected band pin goes High. Analog circuit power supply.
7 8
BU VCC1
9
10
9
MIXout1
Mixer outputs. 10 MIXout2
11
GND1
-- --3--
--
Analog circuit GND.
CXA3185/3186N
Pin No.
Symbol
Equivalent circuit
VCC2
Pin voltage (V)
Description
12
MS
120k
50k
13
VHFin
13 12
14
UHFin1
14
15 3k 3k
15
UHFin2
18
16 VCC1 50
16
VOSC1
8
8p 3k
600
18
VOSC2
3k 15p
17
GND
19
UOSCB1
19
20
21
22 VCC1
20
UOSCE1
3k
21
UOSCE2
3k
22
UOSCB2
Frequency step mode 1.5 selection. Five modes can be (when open) selected according to the applied voltage. 2.3 VHF input. (VHF) The input format is unbalanced 0 input. (UHF) 0 (VHF) 2.3 UHF input. (UHF) The input method can be 0 selected from balanced input (VHF) or unbalanced input. 2.3 (UHF) 3.0 (VHF) 3.1 (UHF) External resonance circuit 3.5 connection for VHF oscillator. (VHF) 5.0 (UHF) -- GND 3.2 (VHF) 2.9 (UHF) -- (VHF) 2.4 (UHF) External resonance circuit -- connection for UHF oscillator. (VHF) 2.4 (UHF) 3.2 (VHF) 2.9 (UHF)
--4--
CXA3185/3186N
Pin No. 23 24
Symbol VCC2 GND2
8
Equivalent circuit -- --
VCC1
Pin voltage Description (V) -- PLL circuit power supply. -- PLL circuit GND.
25
IFOUT
25
40
2.3
IF output.
VCC2 40k
22
26
LOCK
26
5.0 (Lock) 0.2 (UNLock)
LOCK detection. High when locked, Low when unlocked.
VCC2
22
27
CPE
200 28 500
0.6
NPN transistor connection for varicap diode drive.
28
CPO
27 20k
2.0
Charge pump output. Connect a loop filter.
60k 30p 30p
29
REFOSC
29
4.3
Crystal connection for reference oscillator.
30
VCC3
--
Power supply for external supply.
--5--
CXA3185/3186N
Electrical Characteristics Circuit Current Item Circuit current A Symbol AICCV AICCU Circuit current D DICC
See the Electrical Characteristics Measurement Circuit. (VCC=5 V, Ta=25 C) Measurement conditions VCC1 current, Band switch output open during VHF operation VCC1 current, Band switch output open during UHF operation VCC2 current Min. 30 31 7 Typ. 41 42 11 Max. 55 56 15 Unit mA mA mA
OSC/MIX/IF Amplifier Block Item Symbol Conversion gain 1 CG1 CG2 CG3 CG4 Noise figure 1, 2 NF1 NF2 NF3 NF4 1 % cross CM1 modulation 1, 3 CM2 CM3 CM4
Maximum output power
Pomax fsw1 fsw2 fsw3 fsw4
Switch ON drift 4
Supply voltage drift fst1 4 fst2 fst3 fst4
Measurement conditions VHF operation fRF = 55 MHz VHF operation fRF = 360 MHz UHF operation fRF = 360 MHz UHF operation fRF = 800 MHz VHF operation fRF = 55 MHz VHF operation fRF = 360 MHz UHF operation fRF = 360 MHz UHF operation fRF = 800 MHz VHF operation fD = 55 MHz, fUD = 12 MHz VHF operation fD = 360 MHz, fUD = 12 MHz UHF operation fD = 360 MHz, fUD = 12 MHz UHF operation fD = 800 MHz, fUD = 12 MHz 50 load saturation output VHF operation fOSC = 100 MHz f from 3 s to 3 min after switch ON VHF operation fOSC = 405 MHz f from 3 s to 3 min after switch ON UHF operation fOSC = 405 MHz f from 3 s to 3 min after switch ON UHF operation fOSC = 845 MHz f from 3 s to 3 min after switch ON VHF operation fOSC = 100 MHz f when VCC 5 V changes 5 % VHF operation fOSC = 405 MHz f when VCC 5 V changes 5 % UHF operation fOSC = 405 MHz f when VCC 5 V changes 5 % UHF operation fOSC = 845 MHz f when VCC 5 V changes 5 % --6--
Min. 21 22 26 27
Typ. 24 25 29 30 12 11 8.5 9.5 101 100 96 92 +10
Max. 27 28 32 33 15 14 12.5 13.5
Unit dB dB dB dB dB dB dB dB dB dB dB dB dBm
97 96 92 88 +5
300 400 400 500 150 250 200 250
kHz kHz kHz kHz kHz kHz kHz kHz
CXA3185/3186N
1 Measured value for untuned inputs. 2 Noise figure is the direct-reading value of NF meter in DSB. 3 Desired signal (fD) input level is -30 dBm. Undesired signal (fUD) is 100 kHz, 30 % AM. The measurement value is undesired signal level, it measured with a spectrum analyzer at S/I=46 dBm. 4 Value when the PLL is not operating.
PLL Block Item Symbol CL and DA pins "H" level input voltage VIH "L" level input voltage VIL "H" level input current IIH "L" level input current IIL CE pins "H" level input voltage VIHE "L" level input voltage VILE "H" level input current IIHE "L" level input current IILE CPO (charge pump) ICPO Output current LeakCP Leak current LOCK VLOCKH "H" output voltage VLOCKL "L" output voltage REFOSC Oscillator FXTOSC frequency range CXTOSC Input capacitance VXTOSC Drive level BVL, BVH, BU (Band SW) IBS1 Output current VSAT1 Saturation voltage LeakBS1 Leak current FMT (Band SW) Output current Saturation voltage Leak current Bus timing Data setup time Data hold time Enable waiting time Enable setup time Enable hold time Measurement conditions Min. 3 GND VIH = VCC VIL = GND 3 GND VIHE=VCC VILE=GND 35 100 -30 50 0 -1 Typ. Max. VCC 1.5 -0.1 -2 VCC 1.5 130 -45 75 30 VCC 0.5 Unit V V A A V V A A A nA V V
When locked When unlocked
VCC-0.5 0
3 17.5 200 When ON When ON Sink current = 20 mA When OFF 19 400
12 20.5
MHz pF mVp-p mA mV A mA mV A ns ns ns ns ns
100 0.5
-25 200 3 -7 150 0.1
IBS2 When ON VSAT2 When ON Sink current = 5 mA LeakBS2 When OFF tSD tHD tWE tSE tHE See Timing Chart on Page 15 See Timing Chart on Page 15 See Timing Chart on Page 15 See Timing Chart on Page 15 See Timing Chart on Page 15 300 600 300 300 600
75 0.03
--7--
CXA3185/3186N
Electrical Characteristics Measurement Circuit
+30V
22k 8200p 1.2k 47k 0.047 33p +5V 47k 2SC2785 3.3 1n 2.5o2.5t LOCK IF OUT 1T363 47k 56p 47k 56p 1n 8p 30 29 28 27 26 25 24 23 22 21 4p 20 8p 19 18 17 16 1p 1n 1T362 16p 0.5p 0.5p 7p 47k 3.2o 5.5t 1n 47k 51 BVL
3.0o 2.5t
1n
47k
51
BVH
0.5p
1T363
150p 47k
1T363
XTAL 4MHz 100p
47k
UOSCB2
UOSCE1
VOSC2
GND2
LOCK
VCC3
CPO
REFOSC
UOSCE2
UOSCB1
IFOUT
VCC2
GND
CPE
CXA3185/3186N
MIX out1
MIX out2
UHFin1
1
2
3
4
5
6
7
8
9
2k
10
11
12
13
14
15
1n 4.5t CLOCK DATA ENABLE 56p FMT BVL BVH BU 100 56p 1n 4.5t
1n
1n
UHFin2
1n UHF IN
FMT
BVH
VCC1
BVL
GND1
DA
MS
CL
CE
BU
VHF IN 3.3 +5V 1n
--8--
VHF in
VOSC1
CXA3185/3186N
Description of Functions The CXA3185/3186N is a terrestrial wave broadcast tuner IC which converts frequencies to IF in order to tune and detect only the desired reception frequency of VHF, CATV and UHF band signals. In addition to the mixer, local oscillator and IF amplifier circuits required for frequency conversion to IF, this IC also integrates a PLL circuit for local oscillator frequency control onto a single chip. The functions of the various circuits are described below. 1. Mixer circuit This circuit outputs the frequency difference between the signal input to VHFIN or UHFIN and the local oscillation signal. 2. Local oscillator circuit A VCO is formed by externally connecting an LC resonance circuit composed of a varicap diode and inductance. 3. IF amplifier circuit This circuit amplifies the mixer IF output, and consists of an amplifier stage and low impedance output stage. 4. PLL circuit This PLL circuit fixes the local oscillator frequency to the desired frequency. It consists of a prescaler, main divider, reference divider, phase comparator, charge pump and reference oscillator. The control format supports the 3-wire bus format. The following four modes can be selected according to the combination of the frequency division values of the main and reference dividers.
Mode A-0 A-1 A-2 A-3/4
Main divider 15 bit 14 bit 15 bit 15 bit
Reference divider 1024 fixed 512 fixed 640 fixed 512 fixed
--9--
CXA3185/3186N
Description of Analog Block Operation (See the Electrical Characteristics Measurement Circuit.) VHF oscillator circuit * This circuit is a differential amplifier type oscillator circuit. Pin 18 is the output and Pin 16 is the input. Oscillation is performed by connecting an LC resonance circuit including a varicap to Pin 18 via coupled capacitance, inputting to Pin 16 with feedback capacitance, and applying positive feedback. * The amplifier between Pins 16 and 18 has an extremely high gain. Therefore, care should be taken to avoid creating parasitic capacitance, resistance or other feedback loops as this may produce abnormal oscillation. VHF mixer circuit * The mixer circuit employs a double balance mixer with little local oscillation signal leakage. The input format is base input type, with Pin 12 grounded and the RF signal input to Pin 13. * The RF signal is inserted from the oscillator, converted to IF frequency and output from Pins 9 and 10. * Pins 9 and 10 are open collectors, so power must be supplied externally. The electric potential of Pins 9 and 10 at this time must be DC 4.0 V or more. UHF oscillator circuit * This oscillator circuit is designed so that two collector ground type Colpitts oscillators perform differential oscillation operation via an LC resonance circuit including a varicap. Connect resonance capacitance which consists of colpitts oscillator between Pins 19 and 20, Pins 20 and 21, and Pins 21 and 22. Then an LC resonance circuit including a varicap diode is connected between Pins 19 and 22. UHF mixer circuit * This circuit employs a double balance mixer like the VHF mixer circuit. The input format is base input type, with Pins 14 and 15 as the RF input pins. The input method can be selected from balanced input consisting of differential input to Pins 14 and 15 or unbalanced input consisting of grounding Pin 14 via a capacitor and input to Pin 15. * Pins 9 and 10 are the mixer outputs. * Pins 9 and 10 are open collectors, so power must be supplied externally. The electric potential of Pins 9 and 10 at this time must be DC 4.0 V or more. IF amplifier circuit * The signals frequency converted by the mixer are output from Pins 9 and 10, and at the same time are AC coupled inside the IC and input to the IF amplifier. * Single-tuned filters are connected to Pins 9 and 10 in order to improve the interference characteristics of the IF amplifier. * The signal amplified by the IF amplifier is output from Pin 25. The output impedance is approximately 75 .
--10--
CXA3185/3186N
Description of PLL Block The PLL on this IC supports the 3-wire bus control format. The serial data is input to the DA, CL and CE pins. The data is loaded to the shift register at the clock rise, and latched at the enable fall. Symbol CE CL DA LOCK 3-wire bus control Enable input Clock input Data input Lock signal output
1) Mode Setting Method The modes for each frequency step are set according to the MS pin voltage. Mode A-0 A-1 A-2 A-3 A-4 MS pin voltage 0 to 0.15VCC OPEN 0.45VCC to 0.55VCC 0.65VCC to 0.75VCC 0.85VCC to VCC Main divider 15 bit 14 bit 15 bit 15 bit 15 bit Reference divider 1024 512 640 512 512 Reference frequency 3.90625 kHz 7.8125 kHz 6.25 kHz 7.8125 kHz 7.8125 kHz Frequency step 31.25 kHz 62.5 kHz 50 kHz 62.5 kHz 62.5 kHz Control word length Total 19 bits Total 18 bits Total 19 bits Total 19 bits Total 27 bits
Frequency step is for when X'tal OSC = 4 MHz. 2) Programming * The VCO lock frequency is obtained according to the following formula. fosc = fref x 8 x (32 M + S) fosc : local oscillator frequency fref : reference frequency 8 : prescaler fixed frequency division ratio M : main divider frequency division ratio S : swallow counter frequency division ratio The variable frequency division ranges of M and S are as follows, and are set as binary. 32 M 1023 (32 M 511 for A-1 mode) 0 S 31 * The PLL control data is comprised of the above frequency data and the band switch control data.
--11--
CXA3185/3186N
2-1) The CXA3185N control format is as follows. 2-1-1 : A-0/A-2/A-3 Modes (19-bit data format) Front bit MSB BU FMT BVH BVL M9 M8 M7 M6 M5 2-1-2 : A-1 Mode (18-bit data format) Front bit MSB BU FMT BVH BVL M8 M7 2-1-3 : A-4 Mode (27-bit data format) Front bit MSB BU FMT BVH BVL M9 M8 M7 X CP T1 CD X R1 R0 ) X: Don't care S0 to : M0 to : BVL : BVH : FMT : BU : CP : T1 : CD : R0, R1: swallow counter frequency division ratio setting main divider frequency division ratio setting VL band switch control VH band switch control FM trap switch control UHF band switch control charge pump current switching test mode selection charge pump OFF reference divider frequency division ratio setting
M4
M3
M2
M1
M0
S4
S3
S2
LSB S1 S0
M6
M5
M4
M3
M2
M1
M0
S4
S3
S2
LSB S1 S0
M6 X
M5
M4
M3
M2
M1
M0
S4
S3
S2
LSB S1 S0
(output PNP Tr ON when "1") (output PNP Tr ON when "1") (output PNP Tr ON when "1") (output PNP Tr ON when "1") (200 A when "1", 50 A when "0") (when "1") (when "1") (See the table below.)
Reference Divider Frequency Division Ratio Table R1 0 1 X ) X: Don't care R0 1 1 0 Reference divider 1024 512 640
--12--
CXA3185/3186N
2-2) The CXA3186N control format is as follows. The BU and FMT data order is switched for the CXA3185N. In this case the control format is as follows. 2-2-1 : A-0/A-2/A-3 Modes (19-bit data format) Front bit MSB FMT BU BVH BVL M9 M8 M7 M6 M5 2-2-2 : A-1 Mode (18-bit data format) Front bit MSB FMT BU BVH BVL M8 M7 2-2-3 : A-4 Mode (27-bit data format) Front bit MSB FMT BU BVH BVL M9 M8 M7 X CP T1 CD X R1 R0 ) X: Don't care
M4
M3
M2
M1
M0
S4
S3
S2
S1
LSB S0
M6
M5
M4
M3
M2
M1
M0
S4
S3
S2
S1
LSB S0
M6 X
M5
M4
M3
M2
M1
M0
S4
S3
S2
S1
LSB S0
S0 to : M0 to : BVL : BVH : FMT : BU : CP : T1 : CD : R0, R1:
swallow counter frequency division ratio setting main divider frequency division ratio setting VL band switch control VH band switch control FM trap switch control UHF band switch control charge pump current switching test mode selection charge pump OFF reference divider frequency division ratio setting
(output PNP Tr ON when "1") (output PNP Tr ON when "1") (output PNP Tr ON when "1") (output PNP Tr ON when "1") (200 A when "1", 50 A when "0") (when "1") (when "1") (See the table below.)
Reference Divider Frequency Division Ratio Table R1 R0 Reference divider 0 1 1024 1 1 512 X 0 640 ) X: Don't care
--13--
CXA3185/3186N
3) 3-wire Bus Data Format
A-1 Mode (18-bit data format)
Band switch data
BU /FMT FMT /BU
Frequency data M7 M6 M5 M4 M3 M2 M1 M0 S4 S3 S2 S1 S0
BVH BVL M8
DATA 1 CLOCK 4 5 18
ENABLE
A-0/A-2/A-3 Modes (19-bit data format)
Band switch data
BU /FMT FMT /BU
Frequency data M8 M7 M6 M5 M4 M3 M2 M1 M0 S4 S3 S2 S1 S0
BVH BVL M9
DATA 1 CLOCK 4 5 19
ENABLE
A-4 Mode (27-bit data format)
Band switch data
BU /FMT FMT /BU
Frequency data M8 S3 S2 S1 S0 X CP T1
Test data CD X R1 R0 X
BVH BVL M9
DATA 1 CLOCK 4 5 19 20 27
ENABLE
--14--
CXA3185/3186N
4) Bus Timing Chart
tSD
tHD
DATA
3V 1.5V
CLOCK
3V 1.5V
ENABLE
3V 1.5V tWE tSE tHE
tSD = Data setup time tHD = Data hold time tSE = Enable setup time tHE = Enable hold time tWE = Enable waiting time
--15--
CXA3185/3186N
Circuit current vs. Supply voltage 1 45 UHF 15
Circuit current vs. Supply voltage 2
AICC - Circuit current [mA]
VHF
DICC - Circuit current [mA]
40
10
35 4.7
4.8
4.9
5.0
5.1
5.2
5.3
5.4
5
4.7
4.8
4.9
5.0
5.1
5.2
5.3
5.4
VCC1 - Supply voltage [V] Band SW output voltage vs. Output current (BU, BVH, BVL) 9.2
VCC2 - Supply voltage [V] Band SW output voltage vs. Output current (FMT) 9.2
9.0
VCC3=9V
9.0 VCC3=9V
8.8
8.8
Output voltage [V]
Output voltage [V]
VCC3=5V
8.6
8.6
5.0
5.0 VCC3=5V
4.8
4.8
4.6
4.6
4.4
0
5
10
15
20
25
4.4
0
1
2
3
4
5
6
Output current [mA] I/O characteristics (Untuned input) 20
Output current [mA]
0
IF output level [dBm]
-20 fRF=100MHz (VHF) fRF=450MHz (UHF) fIF is both f=45MHz -40
-60 -60
-50
-40
-30
-20
-10
0
10
RF input level [dBm]
--16--
CXA3185/3186N
Conversion gain vs. Reception frequency (Untuned input) 40 fIF=45MHz 35
Noise figure vs. Reception frequency (Untuned input, in DSB) 20 fIF=45MHz
CG - Conversion gain [dB]
NF - Noise figure [dB]
30 25 20 15 10 5 0 0 100 200 300 400 500 600 700 800 900 Reception frequency [MHz] Next adjacent cross modulation vs. Reception frequency (Untuned input) 120
VHF (Low) VHF (High) UHF
15
VHF (Low) VHF (High)
10
UHF
5
0
0
100 200 300 400 500 600 700 800 900 Reception frequency [MHz]
Oscillation frequency power supply fluctuation (PLL off) 400 300 200
VHF (High) VHF (Low) UHF VCC+5% VCC-5% (VCC=5V)
CM - Cross modulation [dB]
100
+B drift [kHz]
80 60 40 20 0
fIF=45MHz fUD=fD+12MHz fUD=fD-12MHz (100kHz, 30% AM)
100 0 -100 -200 -300
0
100 200 300 400 500 600 700 800 900 Reception frequency [MHz]
-400
0
100 200 300 400 500 600 700 800 900 Oscillation frequency [MHz]
PCS beat characteristics +20 +10 0 -10 fIF
IF output level [dBm]
-20 -30 -40 -50 fBeat -60 -70 -80 fLocal=129MHz fP=83.25MHz fC=86.83MHz, (fP-12dB) fS=87.75MHz, (fP-1.7dB) fIF=45.75MHz fBeat=fIF920kHz
-30
-20
-10
0
+10
+20
SG output level [dBm] (fP level)
--17--
CXA3185/3186N
Tuning Response Time
30
VHF (Low) 95MHz VHF (High) 395MHz T=70ms
20
Varicap voltage [V]
10
0
5.0V/div offset 10.0V -90,0000ms 10,0000ms 20.0ms/div 110,000ms
UHF 413MHz UHF 847MHz 30 T=70ms
20
Varicap voltage [V]
10
0
5.0V/div offset 10.0V -90,0000ms 10,0000ms 20.0ms/div 110,000ms
--18--
CXA3185/3186N
IF output spectrum
RL=0dBm 10dB/div
VHF (Low) fRF=55MHz fLO=100MHz RF input level : -40dBm
IF output [dBm]
CENTER 45.0MHz RES BW 1.0kHz
VBW 10Hz
SPAN 100.0kHz SWP 30.0s
IF output spectrum
RL=0dBm 10dB/div
VHF (High) fRF=350MHz fLO=395MHz RF input level : -40dBm
IF output [dBm]
CENTER 45.0MHz RES BW 1.0kHz
VBW 10Hz
SPAN 100.0kHz SWP 30.0s
--19--
CXA3185/3186N
IF output spectrum
RL=0dBm 10dB/div
UHF (Low) fRF=800MHz fLO=845MHz RF input level : -40dBm
IF output [dBm]
CENTER 45.0MHz RES BW 1.0kHz
VBW 10Hz
SPAN 100.0kHz SWP 30.0s
--20--
CXA3185/3186N
VHF Input Impedance
j50
j25
j100
0
50
50MHz 1000p
12
13
VHFin
S11 15
350MHz
-j25
-j100
-j50
UHF Input Impedance
j50
j25
j100
UHFin1
BYP
0
14 50 1000p
UHFin2
S11
350MHz
-j25
800MHz
-j100
-j50
--21--
CXA3185/3186N
IF Output Impedance
j50
j25
j100
0
50
45MHz
-j25
-j100
-j50
--22--
CXA3185/3186N
Package Outline
Unit : mm
30PIN SSOP (PLASTIC)
+ 0.2 1.25 - 0.1 9.7 0.1
0.10
30
16
5.6 0.1
A
1 + 0.1 0.22 - 0.05 0.13 M
15 0.65 + 0.05 0.15 - 0.02
0.1 0.1
0 to 10 NOTE: Dimension "" does not include mold protrusion. DETAIL A
PACKAGE STRUCTURE
PACKAGE MATERIAL SONY CODE EIAJ CODE JEDEC CODE SSOP-30P-L01 SSOP030-P-0056 LEAD TREATMENT LEAD MATERIAL PACKAGE MASS EPOXY RESIN SOLDER/PALLADIUM PLATING 42/COPPER ALLOY 0.1g
NOTE : PALLADIUM PLATING This product uses S-PdPPF (Sony Spec.-Palladium Pre-Plated Lead Frame).
--23--
0.5 0.2
7.6 0.2

▲Up To Search▲

Price & Availability of CXA3185

	To Download CXA3185 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .